The woman said Walker encouraged her to end the pregnancy, saying that the time wasn’t right for a baby, The Daily Beast reported. In the report published late Monday, the news outlet said it reviewed a receipt showing her $575 payment for the procedure, along with a get-well card from Walker and her bank deposit records showing the image of a $700 personal check from Walker dated five days after the abortion receipt. The Daily Beast spoke to the former girlfriend, who asked that her name not be used out of concerns for her privacy. The candidate called the accusation a “flat-out lie” and said he would sue. Senate in Georgia, paid for an abortion for his girlfriend in 2009, according to a new report. Herschel Walker, who has vehemently opposed abortion rights as the Republican nominee for U.S. The Wheel works without any wine configuration in flatout2.Please log in to bookmark this story. 360 for F1 cars and 540 for modern rally cars). Especially the steering hardware lock is useful in certain racing games such as F1 2017 and Dirt Rally to allow for a more realistic steering experience by setting the hardware lock angle to the value of the actual vehicle (e.g. For general gamepad or joystick settings that may also apply to Logitech wheels, please refer to the Gamepad wiki page.Īs of version 0.6.0, oversteer contains compatibility modes for the following wheels:īesides testing the wheel, oversteer allows to configure the following aspects of the wheels:Īdditional settings might be enabled by installing the new-lg4ff-dkms-git AUR device driver. Logitech wheels can be configured via the oversteer tool from the oversteer AUR package. # ffcfstress -d /dev/input/event15 position center force #FLATOUT 2 KEY CODE CODE#WingMan Formula Force GP"Įvent: time 1295173625.476950, type 3 (Absolute), code 0 (X), value 439Įvent: time 1295173625.476983, type 0 (Reset), code 0 (Reset), value 0Įvent: time 1295173625.484827, type 3 (Absolute), code 0 (X), value 428įfcfstress, which is provided by joyutils, can be used to test the force feedback. Input device ID: bus 0x3 vendor 0x46d product 0xc293 version 0x100 #FLATOUT 2 KEY CODE DRIVER#$ evtest /dev/input/event15 Input driver version is 1.0.0 evtest then shows the events coming from the wheel: When using evtest for testing, instead of the js0 as device handler eventX is needed, which in this case is event15 for a Formula Force GP wheel. In case that only events should be displayed, -event can be added as flag. #FLATOUT 2 KEY CODE FULL#Whenever the input is changed, jstest will print the full state of the device. $ jstest /dev/input/js0 Driver version is 2.1.0. To test the wheel with jstest simply call it with the device handler (in this case with a G29 wheel and js0): A graphical version of jstest is available in the AUR as jstest-gtk-git AUR. An alternative is evtest which can be installed via the evtest package. One common tool is jstest which can be installed via the joyutils or the linuxconsole packages. Please memorize the Handlers, here event15 and js0, as these will be necessary to call the tools for testing and configuring the wheel.įor testing the wheel there are multiple tools that can be accessed via the command-line. #FLATOUT 2 KEY CODE INSTALL#If you do not see your Logitech listed as an input device, you need to install usb_modeswitch package. If using a Logitech Wheel, make sure it is set to PS3 mode otherwise it will not work.Ĭhecking input device $ cat /proc/bus/input/devices I: Bus=0003 Vendor=046d Product=c293 Version=0100 # dmesg usb 5-2: new low speed USB device using uhci_hcd and address 6 $ lsusb Bus 005 Device 006: ID 046d:c293 Logitech, Inc. When the wheel is plugged in, the following commands can be used to identify the wheel:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |